Revision history for PatchHeadphones
Additions:
//note: if you don't want to re-do this work before every session - **save your patchbay configuration now!** You can also set this up in your default song so it's ready to go at tracking time. Many companies make decent and inexpensive multi-channel headphone amps, some quite usable ones under $100.//
Deletions:
Additions:
//[If you have one or more free channels left in your mixer, you can also have reverb in your headphone mixes - just patch one or both of the outputs of one of your reverb aux back to the inputs of one or two free mixer channels, and voila; they're as free to be "auxed" over to your headphone mixes as any other mixer channel is. Remember never to "aux" them back to **themselves** though - feedback will result]//
Deletions:
Additions:
//note: if you don't want to re-do this work before every session - **save your patchbay configuration now!** You can also set this up in your default song so it's ready to go at tracking time. Many companies make good inexpensive headphone amps.//
Deletions:
Additions:
//note: if you only want to to this once - **save your patchbay configuration now!** You can also set this up in your default song so it's ready to go at tracking time. Many companies make good inexpensive headphone amps.//
Deletions:
Additions:
**To create a separate headphone mix:**
1) Connect audio cables from the Interface's Out 1 and 2 jacks to the headphone amp.
2) Select an Aux Bus to use for the headphone mix. (We are using Aux Bus #1 for the example.)
3) In the Mixer Window, set the Aux Bus 1 mode switch to Stereo by pushing the Mono/Stereo button. (It is found below the word "Mono". The default send setting for this Aux Bus is mono; pressing the button lights the button's LED and changes the operating mode for the Aux Bus to stereo.)
4) In the Patch Bay Window, drag the Interface, Sub-Mixer and Mixer FX objects onto the Patch Bay desktop.
5) Clear the patch cables that connect the Sub-Mixer L/R main outputs to the Interface's #1 and #2 outputs. (Click on the cable to highlight it; then, use the Clear Patches command in the Edit menu.)
6) Connect a Patch Bay cable from the Mixer FX Send 1L to the Interface Out 1.
7) Connect another Patch Bay cable from the Mixer FX Send 1R to the Interface Out 2.
8) In the Mixer Window, enable the Aux Send 1 button for any channel that you want to send to the headphone mix.
9) You can then change the headphone mix level for each of the active channels individually by using the Amount knob in the Aux Send. (The default value is "0dB".)
10) Note: The default mode of the Aux Send is "Post". Using this setting, the performer's headphone mix will be affected by changes made to the engineer's control room mix (such as level or panning). Switching the mode to "Pre" allows the headphone mix to remain the same, ignoring changes made to the fader levels. Using this mode, some channels can even be turned completely off in the control room, but remain in the performer's headphone mix.
**Single Headphone Cue Mix using the IF-MEC Main Outs**
**Single Headphone Cue Mix using the IF-442 Main Outs**
**To create a separate headphone mix with an A8oT-24 module:**
1) Connect audio cables from the MEC A8oT-24 module's Out 1 and 2 jacks to the headphone amp. (Any of the module's outputs could be used.)
2) Select an Aux Bus to use for the headphone mix. (We are using Aux Bus #1 for the example.
3) In the Mixer Window, set the Aux Bus 1 mode switch to Stereo by pushing the Mono/Stereo button. (It is found below the word "Mono". The default send setting for this Aux Bus is mono; pressing the button lights the button's LED and changes the operating mode for the Aux Bus to stereo.
4) In the Patch Bay Window, drag the MEC Modules and Mixer FX objects onto the Patch Bay desktop.
5) Connect a Patch Bay cable from the Mixer FX Send 1L to the MEC A8oT-24 module's Out 1.
6) Connect another Patch Bay cable from the Mixer FX Send 1R to the MEC A8oT-24 module's Out 2.
7) In the Mixer Window, enable the Aux Send 1 button for any channel that you want to send to the headphone mix.
8) You can then change the headphone mix level for each of the active channels individually by using the Amount knob in the Aux Send. (The default value is "0dB".)
9) Multiple headphone mixes could be created by using additional MEC outputs to feed other headphone amps. Choose a different Aux Send, and follow the instructions above.
**Creating 4 Separate Stereo Headphone Cues with an IF-MEC 8 Output Module **
//note: if you only want to to this once - **save your patchbay configuration now!** You can also set this up in your default song so it's ready to go at tracking time. Behringer PowerPlays make good inexpensive headphone amps.//
1) Connect audio cables from the Interface's Out 1 and 2 jacks to the headphone amp.
2) Select an Aux Bus to use for the headphone mix. (We are using Aux Bus #1 for the example.)
3) In the Mixer Window, set the Aux Bus 1 mode switch to Stereo by pushing the Mono/Stereo button. (It is found below the word "Mono". The default send setting for this Aux Bus is mono; pressing the button lights the button's LED and changes the operating mode for the Aux Bus to stereo.)
4) In the Patch Bay Window, drag the Interface, Sub-Mixer and Mixer FX objects onto the Patch Bay desktop.
5) Clear the patch cables that connect the Sub-Mixer L/R main outputs to the Interface's #1 and #2 outputs. (Click on the cable to highlight it; then, use the Clear Patches command in the Edit menu.)
6) Connect a Patch Bay cable from the Mixer FX Send 1L to the Interface Out 1.
7) Connect another Patch Bay cable from the Mixer FX Send 1R to the Interface Out 2.
8) In the Mixer Window, enable the Aux Send 1 button for any channel that you want to send to the headphone mix.
9) You can then change the headphone mix level for each of the active channels individually by using the Amount knob in the Aux Send. (The default value is "0dB".)
10) Note: The default mode of the Aux Send is "Post". Using this setting, the performer's headphone mix will be affected by changes made to the engineer's control room mix (such as level or panning). Switching the mode to "Pre" allows the headphone mix to remain the same, ignoring changes made to the fader levels. Using this mode, some channels can even be turned completely off in the control room, but remain in the performer's headphone mix.
**Single Headphone Cue Mix using the IF-MEC Main Outs**
**Single Headphone Cue Mix using the IF-442 Main Outs**
**To create a separate headphone mix with an A8oT-24 module:**
1) Connect audio cables from the MEC A8oT-24 module's Out 1 and 2 jacks to the headphone amp. (Any of the module's outputs could be used.)
2) Select an Aux Bus to use for the headphone mix. (We are using Aux Bus #1 for the example.
3) In the Mixer Window, set the Aux Bus 1 mode switch to Stereo by pushing the Mono/Stereo button. (It is found below the word "Mono". The default send setting for this Aux Bus is mono; pressing the button lights the button's LED and changes the operating mode for the Aux Bus to stereo.
4) In the Patch Bay Window, drag the MEC Modules and Mixer FX objects onto the Patch Bay desktop.
5) Connect a Patch Bay cable from the Mixer FX Send 1L to the MEC A8oT-24 module's Out 1.
6) Connect another Patch Bay cable from the Mixer FX Send 1R to the MEC A8oT-24 module's Out 2.
7) In the Mixer Window, enable the Aux Send 1 button for any channel that you want to send to the headphone mix.
8) You can then change the headphone mix level for each of the active channels individually by using the Amount knob in the Aux Send. (The default value is "0dB".)
9) Multiple headphone mixes could be created by using additional MEC outputs to feed other headphone amps. Choose a different Aux Send, and follow the instructions above.
**Creating 4 Separate Stereo Headphone Cues with an IF-MEC 8 Output Module **
//note: if you only want to to this once - **save your patchbay configuration now!** You can also set this up in your default song so it's ready to go at tracking time. Behringer PowerPlays make good inexpensive headphone amps.//
Deletions:
Connect audio cables from the Interface's Out 1 and 2 jacks to the headphone amp.
Select an Aux Bus to use for the headphone mix. (We are using Aux Bus #1 for the example.)
In the Mixer Window, set the Aux Bus 1 mode switch to Stereo by pushing the Mono/Stereo button. (It is found below the word "Mono". The default send setting for this Aux Bus is mono; pressing the button lights the button's LED and changes the operating mode for the Aux Bus to stereo.)
In the Patch Bay Window, drag the Interface, Sub-Mixer and Mixer FX objects onto the Patch Bay desktop.
Clear the patch cables that connect the Sub-Mixer L/R main outputs to the Interface's #1 and #2 outputs. (Click on the cable to highlight it; then, use the Clear Patches command in the Edit menu.)
Connect a Patch Bay cable from the Mixer FX Send 1L to the Interface Out 1.
Connect another Patch Bay cable from the Mixer FX Send 1R to the Interface Out 2.
In the Mixer Window, enable the Aux Send 1 button for any channel that you want to send to the headphone mix.
You can then change the headphone mix level for each of the active channels individually by using the Amount knob in the Aux Send. (The default value is "0dB".)
Note: The default mode of the Aux Send is "Post". Using this setting, the performer's headphone mix will be affected by changes made to the engineer's control room mix (such as level or panning). Switching the mode to "Pre" allows the headphone mix to remain the same, ignoring changes made to the fader levels. Using this mode, some channels can even be turned completely off in the control room, but remain in the performer's headphone mix.
Single Headphone Cue Mix using the IF-MEC Main Outs
Single Headphone Cue Mix using the IF-442 Main Outs
To create a separate headphone mix with an A8oT-24 module:
Connect audio cables from the MEC A8oT-24 module's Out 1 and 2 jacks to the headphone amp. (Any of the module's outputs could be used.)
Select an Aux Bus to use for the headphone mix. (We are using Aux Bus #1 for the example.
In the Mixer Window, set the Aux Bus 1 mode switch to Stereo by pushing the Mono/Stereo button. (It is found below the word "Mono". The default send setting for this Aux Bus is mono; pressing the button lights the button's LED and changes the operating mode for the Aux Bus to stereo.
In the Patch Bay Window, drag the MEC Modules and Mixer FX objects onto the Patch Bay desktop.
Connect a Patch Bay cable from the Mixer FX Send 1L to the MEC A8oT-24 module's Out 1.
Connect another Patch Bay cable from the Mixer FX Send 1R to the MEC A8oT-24 module's Out 2.
In the Mixer Window, enable the Aux Send 1 button for any channel that you want to send to the headphone mix.
You can then change the headphone mix level for each of the active channels individually by using the Amount knob in the Aux Send. (The default value is "0dB".)
Multiple headphone mixes could be created by using additional MEC outputs to feed other headphone amps. Choose a different Aux Send, and follow the instructions above.
Creating 4 Separate Stereo Headphone Cues with an IF-MEC 8 Output Module
Additions:
=====How do I create a Headphone Mix?=====
//(originally part of EMU's Paris Pro FAQs)//
----
//[If you have one or more free channels left in your mixer, you can also have reverb in your headphone mixes - - just patch one or both of the outputs of one of your reverb aux back to the inputs of one or two free mixer channels, and voila; they're free to be "auxed" over to the headphone mixes as well.]//
//(originally part of EMU's Paris Pro FAQs)//
----
//[If you have one or more free channels left in your mixer, you can also have reverb in your headphone mixes - - just patch one or both of the outputs of one of your reverb aux back to the inputs of one or two free mixer channels, and voila; they're free to be "auxed" over to the headphone mixes as well.]//
